Комментарии:
Thabk you, ia the programmer and six pin usb to serial adapter the same thing? I see these adapters on amazon?
ОтветитьThese tutorials are very useful for me, thank you!
ОтветитьNote that erasing memory (+1m52) is done by setting it to xFF, not x00.
Ответить🥑🥑🥑🥑🥑🥑🥑🧇🧇🧇🧇🧇🧇
ОтветитьGreat job Mr. Davis.
ОтветитьHey mate I'm grateful for the content.
I've one last question in my head, is there any difference if we use USB to upload code vs doing the last process like using one Arduino to program another Arduino.
😊😊
hello sir do you have some videos on BLDC motor control with stm32 code which is in hover board i want to learn code writing for that
Ответитьsir do you have some videos om bldc motor control with stm32 code which is in hover board i want to learn code writing for that
ОтветитьAmazing series man, thank you
ОтветитьCan Flash memory and EPROM be programmed by Ethernet communication? specifically when we are dealing in Modbus TCP/IP
ОтветитьExcelent video tutorial
ОтветитьComplicated stuff made simple and straight to the point. Although the content is not hard, the process of figuring it out could be hard in a sense that it's time consuming. These videos are short cuts that bypassed all the readings and findings and get you to the destination in matter of minutes. Thank you for your efforts.
Ответитьfinally someone that explains it correctly. Thank you!
ОтветитьThank You!
ОтветитьI am trying to program an STM32 microcontroller without using a programmer, would this method work for that?
ОтветитьYou rock Mitch, thanks for taking the time to make this series. Valuable content!
ОтветитьMitch thanks for unintentionally answering something I had wondered if safe to do. In using the Uno to program the chip on breadboard both having separate supplies, only needing to common grounds of the USB PC supply and the battery pack supplying the breadboard.
ОтветитьWhat a amazing and didactic content! Best regards from Brazil
ОтветитьWhen I try to upload the blink sketch using another Arduino UNO as a programmer, I am getting the following error message:
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.05s
avrdude: Device signature = 0x000000 (retrying)
Reading | ################################################## | 100% 0.03s
avrdude: Device signature = 0x000000 (retrying)
Reading | ################################################## | 100% 0.03s
avrdude: Device signature = 0x000000
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
avrdude done. Thank you.
Could anyone please tell me how I can go about to fix this issue?
If I program the barebones ATMega328P microcontroller using an Arduino UNO board as the programmer, am I erasing the bootloader present on the ATMega328P microcontroller? If I ever want to program the ATMega328P microcontroller via USB (after re-inserting it back onto its respective Arduino UNO board), will I have to burn the bootloader?
ОтветитьCan one make their own bootloader? For Arduino that is
ОтветитьHello, how have you learned this interesting topics? Working? Studying? Or reading by yourself in different refences? Thank you very much!
ОтветитьWhy do they recommend you flash a bootloader onto the attiny when it doesn't have a usb port?
ОтветитьLove the series! Thank you!
ОтветитьWhat is flashing of the application
ОтветитьPlease tell me How to do the same thing with the Texas instruments MCU (like TMS320F2802)?
ОтветитьI really enjoyed all your videos
I just want to know if it is possiblle to use an arduino uno as a programmer for an stm32 microcontroller
Thanks in advance
i like it . thanks for your hard work
Ответитьhow did you learn this without videos like this? Any chance you could provide a roadmap?
ОтветитьHow do we know this programer is Arduino as isp?
ОтветитьThe quality of the content you are producing speaks for the effort you are putting in. Incredible job!
Ответитьclearly explained all aspects of programming the arduino via bootloader & via an isp programmer.. excellent! thanks mitch..
ОтветитьHow to write your own bootloader? I really appreciate a video talking about this (I think it's gonna be several videos but anyway, I eould really like to do almost all things on my own as you have shown on your videos) thank you.
ОтветитьI need to ask the one dislike person (whyyyyyyyyyyyyyyy !!)
ОтветитьIt gives me error invalid signature 0xffffff for atmega 328p U , i tried like so many things but still cant be able to burn the bootloader in this chip through arduino, please need some help with this
ОтветитьExcellent videos in beautiful clear English! You always make all signal connections after your target has been powered. Something ever die doing it this way? Maybe make the connections first and turn on the power last?
ОтветитьDamn, I've learned quite a bit with this series
ОтветитьI accidentally corrupted bootloader of nano, tried to make that work as before using another nano. But eventually fails. But this video makes quite lots of info, great work.👍🏻
ОтветитьWhy is the led in the programmer also blinking in the last example?
ОтветитьGreat work thank you, i was wondering why you did not use the ICSP pins using jumper wires ? rather than the standard pins !
ОтветитьDisregard Mitchel I got it working with the avr-gcc toolchain.
ОтветитьGreat video. I’ve been looking for an explanation like this for days because most videos just show you how to use a programmer but don’t explain what’s going on. You’re very good at explaining things. Keep up the great work.
ОтветитьGreat video. Keep working
ОтветитьGreat Job! Thank you!
ОтветитьBlah blah blah blah killed me 😂. I just use an ftdi friend
ОтветитьThank you for the video!
Ответить