Комментарии:
You finally discovered stencil fonts? I mean they've been in heavy use since the 1700s, but okay 😂
ОтветитьGRIND WELD PAINT REPEAT
ОтветитьWhat router is that?
ОтветитьGreat video. I was wondering if you could put out an update video, with how much use and how well it has held up in the last two months. And of course, issues you had, the pros and cons. Thx.
ОтветитьTo engrave bottles you filled them up with water to avoid the terrible material deformation you had.
ОтветитьUse a heat gun when removing the paper off of acrylic.
ОтветитьNice video, it would be even better if you showed the actual amount of time it took to cut out the various pieces. The number of passes is useful information, but cutting in a single pass is not that great if it takes 45 minutes per letter.
Ответитьcould see all those hairs up your nose... how embarrasing
ОтветитьSilly question…why not etch the letters “est 2018” so that you just place them in and not have to line them up?
Ответить1 pass.. well if you go slow enough.. maybe... probably better to cut wood with a blade or carbide bit instead.. waaaaay faster and no scorching and smoke... just use the laser to etch logo or customization/go blind trying to watch it work
ОтветитьThanks for the review. The Falcom 40W is going to the top of my list......
ОтветитьGreat Video, I use allot of acrylic to make LED signs..... If you use a heat gun on the backing for just a few seconds the backing will peel off easily..... Just a suggestion..... Good Luck
Ответить2k?
ОтветитьWhere is the 3/4 inch wood in one pass?? Bullshit!
ОтветитьLooks like an xTool clone. With better cable management.
ОтветитьHow long does it take that you have to replace the laser? also for how many hours do the laser ?
ОтветитьGood Morning. I have a question. What do you with the smoke in the room? I seen the door was open. Is there alot of smoke ?
ОтветитьJacob -ean
ОтветитьDo you think this laser would hold up doing production work? Could it run all day?(5hrs duty out of an 8hr day)
ОтветитьNext time you search for such a font, use the keyword "Stencil", because that's what it is.
Ответитьmaybe a thinner plastic frosted white backing would make the leds brighter, it might be to thick or it just does not come out on camera all that vibrant.
ОтветитьWhen painting the letters, I use masking tape, sticky side up. It helps prevent the letters from moving when painting. Nice job guys!!!!
ОтветитьNice sign, looks like a great laser. Whats the fond you using?
ОтветитьCan it cut plywood? How thick?
ОтветитьWhen placing the small letters use the cut out negative as a placing template align it in the right spot no measuring required use tweezers to grab letters and it goes fast
ОтветитьGRIND WELD PAINT REPEAT Greetings from Colombia!
ОтветитьGrind Weld Paint Repeat
ОтветитьVery nicely done project, thank you.
ОтветитьHi just started watch info regarding lasers today 8/29/23. I have watched so many, yours helped me a lot with my Decisions. Thank You
Side note, I am wanting to start side hustle because I can’t work full time anymore. 24 surgeries 8 in the last 5 years. Mri tomorrow if I need a third back surgery. ( fell off semi in 2017) 😢I need to find things to do to supplement income that doesn’t take to much physically.
Thx
Phil
Does it cut clear Acrylic too?
ОтветитьHi, Great machine!👍💯
ОтветитьShould these laser cutters be running with no enclosure?
ОтветитьGreat video guys. I just went to check this laser on their website. They show "adjustable light beam" with the click of a button. It's like 2 modules in one?. 40w and 22w. If you went over this feature I think I missed it. I know nothing about these lasers . So I've been doing my research and came across the brand. Thank you guys for the tips.
ОтветитьNo fume extraction/exhaust - that's a quick way to get sick real fast. Setting up a fan by an open door or window is not sufficient as I'm sure you already found out. You will still have lots of fumes in your work space - especially if attempting any mass production. Nicely done video though! Tip for removing acrylic masking quicker - use a hair blow dryer on low setting to warm it. Alternatively you can do a quick wipe with mineral spirits, wait a minute or two, then remove the mask in one piece usually.
ОтветитьWhat’s the name of the font? Thanks!
Ответитьwhat about the color engraving how does it do the job
ОтветитьDo you think this Creality machine will work good for engraving custom art designs, logos and text on firearms and knives? If so I might need to invest in one of them.
ОтветитьI LOVE MY NOTEBOOK 😍😍😍
ОтветитьGRIND WELD PAINT REPEAT great job!
Ответитьare you kindasorta sleeping in the structure yet?
ОтветитьGRIND WELD PAINT REPEAT - great sign!
ОтветитьWow! What an amazing machine!
ОтветитьGRIND WELD PAINT REPEAT! Good job!!!!
ОтветитьThey're called "stencil" fonts.
I'm going to have to get one of these lasers for my container build.
Birch-plywood wall interiors with laser-cut holes for flush mount switches and outlets.
This is the solution I was looking for.
Thanks!
I like your catchphrase 'grind, weld paint repeat" especially when you're working on your place. You both work well together and I like your videos.
ОтветитьGrind Weld Paint Repeat!! Love the sign!
ОтветитьThe calm white n The Blue
ОтветитьIsaiah 33:15-16
King James Version
15 He that walketh righteously, and speaketh uprightly; he that despiseth the gain of oppressions, that shaketh his hands from holding of bribes, that stoppeth his ears from hearing of blood, and shutteth his eyes from seeing evil;
16 He shall dwell on high: his place of defence shall be the munitions of rocks: bread shall be given him; his waters shall be sure. Gods blessings over you