PLC Programming Tutorial for Beginners_ Part 2

Great tutorials, thank you so much!
I am total beginner in PLC programming.
Would appreciate to get an advice about synchronous speed control of 4 servo motors and change the speed according to a couple of parameters. Also, HMI is supposed to be used for this purpose.

Do you guys have tutorials on the wincc application?

Your tutorials are very impressive, am grateful to your impartation. Thanks.
I am currently operating on 2# electric gas kilns and using plc board in operating to the system, so your program is helpful to me.
Keep up with your good job.

What about subroutines , do have any tutorials explaining those, thank you , and great thing you're doing.

Really Awesome😍

Hey man i want to program a plc using c instead of ladder logic so can u help me with that

Great teaching

i appreciate it. This video was so helpful. Thank you!!

The world is simple, just keep it simple 😀

Why is the high level energized when liquid is on high level but low level is energized when there is not liquid on low level?

This is lovely, I really gained a lot of knowledge watching this video

installed, everything works, thanks!

Thank you so much for such a good video.

Thanks a lot for the tutorial, I just have two questions: since the stop button is normally closed, doesn't it just reset the flip flops immediately? Also actuating the stop button seems to just discontinue power to the reset part of the flop, please explain how the stop button works. Thank you.

I have a question. Suppose you are dealing with a process with entails the separation of oil and water. The quantity (volume) of oil and water is not always fixed but varies once the liquid settles. How then do you make real time changes to or how do reprogram the level sensors to meet these new level of oil and water so that we can have as much as possible, an accurate separation process

You're such a good teacher ,I need more illustration on how to link PLC with HMIs thanks

Great Thanks, i have question about program architecture how to start (organize the thinking) how to divide the program start by all protections are first or operation philosophy or what!!!!!!!!!! plz help me i need to organize the program to help any body can understand my program easy

Nice

Respected realpars sir may you please 🙏 make a wiring diagram of all this logic .please

The part 1 and the part 2 are amazing videos. Very easy to understand and follow. I have noticed. The low-level switch is open when there is water, and the high-level switch is closed when there is water. Should not we use the normally closed switch for the low-level switch?

great

Thank youu 🙏🏽

Great video... But i have a small question.. When the liquid reaches to maximum level and high level switch is activated. And mixer and valve are turned on respectively. But when the liquid goes below high level switch the status of high level switch will change and that will affect the entire process... What say?

Really Good broth, it's a very good info!
We hope you to show us more , from your good info!

Great ❤

Thank you very much

it's so insteresting the way that you explained everything
thanks i catch it

shouldn't there be a problem with this code if H level is active and the mixer haven't yet been activated will cause the valve to open prematurely??

I was wondering why Network 3 doesn't trigger when the water level first reaches H_LEVEL and as the MIXER is off.
Is this because Network 3 isn't looking to detect that the MIXER is off, but rather that it has been switched from on to off?

Can we practice it without plc

Feels like this would be easyer in C...

your explanation very easy to teach( crystal clear) thank you sir

Thank you my friend for your videos but i will never use that brand siemens in my life.
Too many useless movements in the software without a reason.
Fatek,Ls, Delta, mitsubishi etc softwares have much more friendly environment.
But again thank you for your videos they are very specific and educational.

NICE SIR

Low level should be negated contact. Otherwise sensor will give out sigal while liquid is above low level sensor and will be resetting dischage valve flip flop.
So if we set LowLVL contact as a NC it will close once level drops below bottom level thus setting on pumps. Of course a relay with NC contact can be used to invert LowLVL signal, but that's aditional cost.

Pretty good

I’m new to this but as i understand you wait until h_level is on and mixer is off to open the valve. Well doesn’t that latch get turned on right after h_level is on before starting the mixer right after filling the tank which then opens the valve before mixer starts even working. Could that be a bug in your code or maybe I didn’t understand it properly?

very well explained ...thank you

good😉

Clear and concise.

What a shit program lol.

Best tutorial i ever seen, thanks alot 👍

nice video, may I know the language used in this programming? is it ladder or FBD?

too bad it's impossible to download the s7 manager

Hi real pars thanks to you, the NC for stop push button is wrong because in this situation you have always 1 on flip flops and program not running

thanks

I am interested PLC programming Learning

very good