Lead Acid/Lithium battery charger make by XH-M603 charge controller (computer power supply charger)

work flowless🎉🎉🎉🎉 ty for showing !!!

Hi. Can i set the connect value to 13.4v and set the disconnect value to 13.7v?

Funny reading the comments. This is not a charger, its a voltage dependant switch. The pcb connects the 2 positive terminals together at a pre-determined set voltage and then dis-connects them when the upper level setting is reached. The 2 negative terminals are already connected together.

can i put diode from charger to this module? to flow the current in one direction

.good video but you should have kept heatsinks exposed to ventilation

Stupid music , can’t you just say how to set up the thing

I want to use this module to charge a 14.4v car battery from an 18v laptop power supply. What is the charging current if the power supply is 65w?

Can this module also be used to charge drill batteries? For example, if I turn on and off the battery, are the settings retained?

Hello, listen to the amps how are they managed? I need to charge a 12v 12A lithium battery pack. If I put a 1A charger on the battery does it get 1A? Thank you

Ciao, per caricare un pacco batterie litio 12v la corrente come viene gestita? Se in entrata metto 1A alla batteria arriva 1A? Grazie

amazing tecnolagy

Hi is possible attach a load in parallel of battery ?? thanks

Nice jobb....

Thos wire terminal connector does not look like needed here :-)

14v is to low set 14.7

Please phone no

Can or will it work to charge a lead acid battery with a LI battery charger?
Can use a li controller on acid batterys?

Heat on capacitor,,,so why put melting glue on it... plus ventilation since you converting power ... improve on the safety and assembly... nothing spectacular

Can I connect it to my 72v ebike battery pack to prevent 100% charging.

Wow, excellent. Possible to make similar charger for lithium 100AH 12..8v battery?

Esa caja de bocadiilos va a recalentar los circuitos integrados

ПОМОГ СПАСИБО

Nice video, but have one question. Can also use this setup for my lifepo4 battery.

how about if the battery of a motor or a car how do I set on a battery charging controller protection?

Haw do you reset the settings?
I bought one a week ago I set it up and naw I wanted to change the settings , but wen I press the set button nothing happens .

can I recharge a lithium 7.5v battery with this board? What's the minimum voltage?

Tell me a best module to charge AA NiCd batteries.

Can this module take input of 20V from laptop charger and charge a Lead Acid 12v battery without any problem? I am worried because the laptop charger output 20v but battery is a 12v battery. Start charge volt i am setting in the module is 11.5 and cutoff voltage i set is 14V.

Is it possible to charge battery when connected to load?

No absorbtion stage. Add some time relay module.

Hi, does it keep the settings in memory if it is disconnected ? thanks !

Nice

I’ve tried to build this to charge my 18650 5 battery pack. Got 20.5v supply in, charge window . 11.5v to 20.4 battery kicks in to charge then off again, is my M603 board faulty??

I want to use the same setup, but with a step down converter. Can you tell me if using this, instead of using a "charger", is harmful for my battery's longevity? (lead acid)

Hi can i connect a laptop 18 b charger to a 18 v power drill battery to charge it ? Can i do it without step up converter ?

How can you control current, if your power supply is 2 A? I know limiting current will increase time but increase battery life

Guy music and a how to video. do not mix your views may go up if you make with no music full subtitles and normal speed. People that know what you are doing will skip anyway. Great idea similar to what I’m making

Thanks for the idea. But can we charge 150 ah lead acid cells with same setup ? Kindly advise...

Working like lithium battery without bms?

One of my requirement is
I want 12v 12amps charger with variable power supply with battery indication and auto cut off circuit...

This is one of the best dyi haven't tried it yet just ordered the parts let you know how it goes

is it working for 12v, 75A car battery?

does not check if batt is full and not taking anymorr amps just voltage control?

Your meter shows the battery voltage is 12.6V but the XH-M603 reads it as 12.2V i.e. the XH-M603 is inaccurate, 0.4V low. This would seem to be a big problem for something controlling lithium batteries. Even lead-acid would be damaged by 0.4V overcharging.

very cool.

Great video! But one question, do you have to re-calibrate the voltage values every time you conect the module or do they keep saved? Thanks in advance for your time.

12v charge to 12v17Amp charjing kaye krneka o yek bar dikhav

hiii

I'm curious about why you used the DC to DC step-up converter. Your Power Supply is set at 12v, right? Why can't we just plug the 12v directly into the Battery Charge Control Board and set the lower limit to 11v and upper limit to 12v? Are the 14v necessary? Why not just set your power supply to 14v from the beginning?